![]() You can also use it after you’ve installed your new hardware to tighten things up. You’ll need a screwdriver to remove the hardware you are replacing. A pencil is always handy to have around during any DIY project. Once you line up the template (or level) to the drawer, you’ll need to make a small mark so you know where to drill when you move the template. Photo Credit: “ pencil” by Tim Taylor is licensed under CC BY 2.0 (Also, see step 1 below for another tip to avoid measuring). Tell an employee that you want the same size screw diameter, but longer or shorter length, depending on the thickness of your drawer and the depth of the screw hole in your pulls. If that’s the case, just measure the thickness of your drawer and go to your local hardware store with your pulls and the screws that it comes with. But keep in mind that depending on the thickness of your drawers or cabinet doors, you may need longer or shorter screws than what is provided. Oftentimes, when you buy the cup pulls, the necessary screws come with them. Obviously, you’ll need the actual cup pulls and screws. But I’m telling you, it’s worth it! You can even make a homemade template using a paper, pencil, and ruler. You can use a level if you absolutely need to or can't spend a few bucks on the template. And it even comes with a standard drill bit. It saves you from doing some measuring and basic math, which is quite the perk for someone like me who is horrible at math. This handy template will make your life so easy while you install your cup pulls! As a side note, it also works for pulls, knobs, and handles. Most likely it will be a Phillips head (aka cross-head) tip. Then you’ll also want the drill bit that fits the type of screws you’ll be using. You’ll probably want a standard drill bit to make the original hole. Kitchen Pull-Out and Built-In Trash Cans.Soft Close Undermount Drawer Slides (glides).Soft Close Side Mounted Drawer Slides (glides).> If installing more than one, repeat process for each knobĪnd you are done! What a big difference a little beautiful hardware can make.Īs you can see, you don’t have to be a DIY professional to update your cabinet hardware and instantly transform your spaces at home! Install new cabinet knobs and handles with ease. Note: If you need to shorten your bolt, trim with a bolt cutter. ![]() > Make sure not to over-tighten, as this can crack your cabinet door or break your knobs > Add the clear rubber washer (optional) then bolt and tighten the fastening with a spanner > Insert the knob into the screw hole and secure back with the metal washer You’re almost there! Here’s how to install your cabinet knobs (or handles and pulls) correctly: > Using your power drill, go ahead and drill the door at the marked screw hole locations > To avoid drilling into the cabinet frame, hold the cabinet door open with one hand as you drill or prop it open with a towel. Unsure of the size? Simply drill a test hole into a piece of scrap wood to test whether the fastening screws will fit. Note: Most cabinet screws need a 4mm diameter hole, so use a power drill with a 4mm twist to create your new screw holes. Like up your cardboard with the cupboard door and poke a nail through to start the screw holes on the door. How? Assume the corner of the piece of cardboard is the corner of the cabinet door, then mark the screw hole locations accordingly. You can even make your own using a piece of cardboard. > If you are installing more than a few knobs, we recommend using a template to make the job not only faster, but to ensure uniformity across the cabinet set. You can pick adhesive up from your local hardware or art supply store. Using a pencil, mark the location you like and install the rest of the hardware accordingly. TIP: If you’re not sure where to place your knobs, stick a piece of reusable putty adhesive to the hardware and try out different spots. > If you are creating new screw holes, measure and mark the new screw hole locations with a pencil Note: If you’re replacing cabinet knobs and can reuse the existing screw holes, you can skip step 2 and 3, and simply insert the new fastening screw into the hole and tighten the knob into place. STEP 2: Measure and mark locations for new cabinet knobs > If you’re switching from a pull to a knob for example, you can hide old holes or damaged surfaces with backplates. Paint over or refinish the patched holes as needed. ![]() > Patch the old holes with a wood filler that matches the finish of your cabinet. These are usually found on the back of the cabinet door > Use a screwdriver to remove each cabinet knob’s fastening screw. If you are replacing cabinet knobs, you’ll need to first remove the old knobs. Power drill (if creating new screw holes)
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |